www.U-LineService.comPhone (414) 354-0300 • FAX (414) 354-7905Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696OnlineService@U-
www.U-LineService.com 10 03/2008CLR2160/CLRCO2175 Ice Makers2. Pull door gasket out of groove (top edge of door only). Start in the middle and pull ou
03/2008 11 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers2. Create a relief (Figure 19) for pivot plate by cutting notch in top corner of overlay p
www.U-LineService.com 12 03/2008CLR2160/CLRCO2175 Ice Makers 3. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon
03/2008 13 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers4. Attach Top Pivot Plate to door handle, on side where hinges will be. Use the two #8-32
www.U-LineService.com 14 03/2008CLR2160/CLRCO2175 Ice MakersChecking Door AlignmentThe unit’s door is aligned at the factory before shipment. However,
03/2008 15 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersCAUTIONPlumbing installation must observe all state and local codes. All water and drain c
www.U-LineService.com 16 03/2008CLR2160/CLRCO2175 Ice Makers• Drain line does not create traps or created traps are vented (see Figure 37).See Figure
03/2008 17 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers2. Carefully push the power cord grommet through the hole in the back panel (see Figure 40
www.U-LineService.com 18 03/2008CLR2160/CLRCO2175 Ice MakersWARNINGTo prevent accidental electrocution, make certain that the floor surfaces surroundi
03/2008 19 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers3. Attach the copper water line to the back of the unit using the supplied clamp and the b
www.U-LineService.com 2 03/2008CLR2160/CLRCO2175 Ice MakersContentsContents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
www.U-LineService.com 20 03/2008CLR2160/CLRCO2175 Ice MakersElectrical SpecificationsCAUTIONElectrical installation must observe all state and local c
03/2008 21 www.U-LineService.comCLR2160/CLRCO2175 Ice Makers2. If the ice maker is not level, adjust the feet on the corners of the unit as necessary
www.U-LineService.com 22 03/2008CLR2160/CLRCO2175 Ice MakersRelocating the Shelves (CLRCO2175)Both the glass shelves in the refrigerator and the inner
03/2008 23 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersInitial Start-UpOnce installation and leveling is complete, the unit is ready for initial
©2008 U-Line CorporationPublication No. 30141E03/2008 Rev. EU-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-i
03/2008 3 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersGeneral PrecautionsUse this appliance for its intended purpose only and follow these genera
www.U-LineService.com 4 03/2008CLR2160/CLRCO2175 Ice MakersInspectionUnwrap and inspect the unit on a flat, level surface capable of supporting its en
03/2008 5 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersYour U-Line product has been designed for either free-standing or built-in installation. Wh
www.U-LineService.com 6 03/2008CLR2160/CLRCO2175 Ice MakersCut-Out Dimensions CLRCO2175Follow the cut-out drawing in Figure 4. The 24-3/16" width
03/2008 7 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersReversing the Door(Black and White Units Only)All U-Line units (except Stainless Steel mode
www.U-LineService.com 8 03/2008CLR2160/CLRCO2175 Ice MakersOther Site RequirementsPower SupplyThe unit requires a grounded and polarized 115 VAC, 60 H
03/2008 9 www.U-LineService.comCLR2160/CLRCO2175 Ice MakersSide-By-Side Installation Instructions CLRCO2175For a complete refreshment center, install
Comments to this Manuals